Sidor som bilder
PDF
ePub
[graphic][merged small][merged small][merged small][merged small][merged small][merged small][merged small]

Principally a case-hardened steel, recommended for machine parts, particularly for the steering mechanism of automobiles, for guiding levers, axle bearings, front and rear axles, rivets, etc.

Standard Alloy Steels for Construc

tional Purposes. Special catalogues.

[blocks in formation]

Like the foregoing, principally a case-hardened steel somewhat harder, more elastic, and allowing a higher degree of hardening. Suitable for cogwheels, levers, spindles, crosspieces, etc., or in general for case-hardened parts which require a comparatively high degree of strength.

[blocks in formation]

Suitable for case-hardening or tough tempering. Case-hardened if a material of a harder nature than the two foregoing qualities is required.

[blocks in formation]

This is a type of nickel steel, with high tensile strength and breaking strain, yet not in any way brittle.

Recommended for use for screw-bolts, etc. in high speed machines or motors, etc.

[blocks in formation]

A steel of greater hardness, with greater capacity for receiving temper than the foregoing and with higher degree of strength, though its toughness is in no way reduced. Suitable for case-hardening.

[graphic][subsumed]

Söderfors

Steel

[blocks in formation]

Owing to an air-hardening process this is a very hard quality, and hence difficult to work. Thus parts required for constructional purposes, and of such a shape that they easily warp when quenched in oil or water, acquire a sufficient degree of hardness simply through air chilling.

This steel is non-magnetic, does not rust, and is remarkable for its toughness and 25% Nickel durability. It cannot be hardened. This steel possesses great power of resistance to electricity, 0.6-0.7 ohm per meter and mm2, which does not vary much according to temperature, as is the case with ordinary steel. It has also high power of resistance to high temperatures, as well as to steam and oxydizing vapours, and is therefore the quality required for valves.

[graphic][merged small][merged small][merged small][merged small][merged small][merged small][merged small][merged small][merged small][merged small]

kel steel, Chrome nickel steel, Vanadium steel, Chrome vanadium steel, in any proportion desired, and if a sufficiently large quantity is ordered.

The composition of the standard qualities (see special catalogue) is the fruit of expert experience during recent years. If a superior alloy constructional steel is required. Söderfors is therefore the right source of supply.

Brand:

The works at Gysinge make Carbon and Alloy Electro Steel of excellent quality for tools of various kinds.

[merged small][merged small][merged small][merged small][merged small][merged small][merged small][merged small][ocr errors]

Electro Tool
Steel

Brands:

Soft, tough, homogeneous, easily forged and welded material, not sensitive to heat; often used with good results as a substitute for Lancashire Iron. The Company's Siemens Martin Rods are used as a speciality for welding purposes and for making Horse Shoe Nails and Conducting Wire. Dead Soft Steels delivered rolled as well as hammered, or in wire rods.

Rolling capacity:

Bars: not below 3/16" round or square.

Wire Rods: from No. 6 B. S. W. G. up to the thickest rods that can be wound in coils. Largest dimensions rolled:

Round: up to and including 9". Square: up to and including 10".

Gysinge Electro Steel Works. View taken from an in aeroplane in 1922

[ocr errors]

Straight flat: 1/16"
1", up to 712" in width
and 26′ in length.

Plates and Sheets of
Thomas Charcoal Steel,
as well as of Siemens
Martin Dead Soft Steel of
up to and including 0.4%
Carbon and, when suitable
specifications are given,
in some cases harder (up
to 0.50/0-60 %). Bent,
pressed, flanged, punched
plates, spade plates, etc.,
boiler headers, flat and
dished are also supplied,
as well as Bar Ends of

Charcoal Dead Soft

Steels

[graphic]

Plates &
Sheets

Finished
Articles

Steel Castings

Thomas & Siemens Martin Charcoal Dead Soft Steel, Off-Cuts of the latter, steel
for tires with round edges, Horse Shoe Steel in current sizes, Handle Steel, and
Fire Bars.

Angles and Bulb Angles, Beams, Channels, Tees & Zees, Rails and Switch-Point
Blanks, Rails, Nails, Rail Spikes, Bolts and Screws, Axle Blanks for Carriages.
Of highest quality Open Hearth Steel on receipt of patterns or drawings.

[merged small][graphic][graphic][merged small][merged small][merged small][graphic][merged small]

Solid Cast Steel Anvils

SÖDERFORS
DANNEMORA

Where anvils of the highest efficiency and durability are required, the right source of supply is Söderfors. They are manufactured from the best ore in the world, i. e. from the Dannemora Mines, situated near the works. This fact combined with experiments and improvements in various details of manufacture obtained from 35 years' experience, guarantees perfection in the anvils. The face is not welded on; the anvils are cast in a single piece, i. e. »all-steel», and are carefully hardened. Before delivery, they are thoroughly tested and inspected. The tempering is done with the utmost precision, so as to avoid chipping, and at the same time to preserve the toughness and resilient properties of the steel.

Söderfors anvils are sold all over the world. They are made in all standard types, and also in special types according to drawings. Special catalogue on application.

Some Standard Types
of Anvils

[blocks in formation]

Brand

[graphic]
[graphic]
[graphic]
[graphic]
« FöregåendeFortsätt »